Guide

How to Prepare an STL File for 3D Printing (Checklist Before You Upload)

Get your STL print-ready: units, watertight meshes, export resolution, wall thickness, overhangs, clearances and orientation, with free tools to check each one.

By Joe Shenton8 min read3D printingFile preparation

You've designed a part, or downloaded one, and you're ready to get it printed. Before you upload it anywhere, it's worth spending ten minutes checking the file. Most of the problems that slow a print job down, or make it come out wrong, are visible in the file before a printer ever touches it.

This guide walks through what to check, in the order we'd check it: units, mesh health, export resolution, then the design details that decide whether a part prints well (walls, overhangs, clearances and orientation). It's written for FDM (filament) printing, which is what most people mean by 3D printing and what most print services, including ours, run.

The quick checklist

If you only read one section, read this one:

Check What "good" looks like
Units Exported in millimetres; the size looks right in a slicer
Mesh Watertight (manifold), no holes, no flipped faces
Resolution Curves look smooth, file isn't absurdly large
Walls At least two extrusion widths thick, ideally 1.2 mm or more
Overhangs Under about 45°, or you've planned for supports
Fit Clearance designed in where parts slide or press together
Size Fits the printer's build volume, or is split into pieces
Format 3MF if your software exports it, otherwise STL

The rest of this post explains each one.

1. Check the units (the most common mistake)

An STL file is just a list of triangles. It stores coordinates but no units, so software opening it has to guess what "25" means. Almost every slicer assumes millimetres. As Prusa's team puts it in their write-up on the 3MF format, STL "doesn't contain any scale, color or material information."

So if your CAD file is set up in inches and exports in inches, a 4-inch bracket arrives as a 4 mm speck. The reverse happens too: a model drawn in metres turns up a thousand times too big.

How to check:

  • Open the file in a free slicer such as PrusaSlicer, Bambu Studio or OrcaSlicer and look at the dimensions it reports.
  • Compare them with one measurement you know, like the length of the part or the diameter of a hole.
  • If it's out by 25.4×, it's an inch/millimetre mix-up. Fix it in your CAD export settings rather than scaling in the slicer, so the next export is right too.

2. Make sure the mesh is watertight

For a slicer to work out what's inside and outside a part, the surface has to be closed: every edge shared by exactly two triangles, with no gaps, overlaps or faces pointing the wrong way. This is called a manifold or watertight mesh. Prusa's modelling guide is blunt about it: holes in the surface or stray internal geometry will stop a model slicing properly.

Common causes:

  • Models built for games, animation or rendering, which only need to look right on screen
  • Two bodies overlapping that were exported without being joined
  • Scans and AI-generated meshes, which often have holes and loose bits
  • Tiny gaps left where surfaces almost, but don't quite, meet in CAD

How to check and fix it:

  • Bambu Studio flags errors with a warning icon in the object list and has a Fix Model option. Bambu's wiki notes this repair uses Microsoft's Netfabb-based service and is only supported on Windows.
  • PrusaSlicer and OrcaSlicer also report and attempt to repair mesh errors on import.
  • Blender includes a 3D Print Toolbox add-on (enable it under Preferences → Add-ons) that checks for non-manifold edges, intersecting faces, thin walls and overhangs.
  • In CAD, the best fix is at the source: combine bodies into one before export, and close any open surfaces.

Automatic repair is good at small holes and flipped faces. It's not good at guessing what you meant when a big chunk of surface is missing, so check the repaired model still looks right.

A watertight mesh also matters for pricing. Instant quote tools, ours included, calculate a part's volume from the mesh to estimate how much plastic it uses. A mesh with holes can produce a volume that's wildly off, which means an estimate that's wildly off.

3. Export at a sensible resolution

CAD software stores curves mathematically. STL can't; it approximates every curve with flat triangles. Export too coarse and round holes come out as visible polygons. Export too fine and you get a huge file with no visible benefit.

Most CAD tools give you a preset (low, medium, high) and the underlying settings:

  • Surface (chordal) deviation: how far a triangle can sit from the true surface
  • Angle (normal) deviation: how sharply neighbouring triangles can change direction

In Fusion, these appear under the mesh refinement options when you export or Save as Mesh, and the Fusion API documentation describes surface deviation as "the maximum distance the mesh can deviate from the actual surface" and normal deviation as the maximum angle between mesh normals and the real surface. SolidWorks, Onshape and FreeCAD have equivalent deviation and angle settings.

For FDM, where the nozzle lays down lines roughly 0.4 mm wide, the high preset in most tools is plenty. If small holes or round bosses look faceted when you zoom in on the export, go finer. If the file is hundreds of megabytes for a palm-sized part, go coarser.

While you're in the export dialog, choose binary STL rather than ASCII if given the choice. It holds the same geometry in a much smaller file.

4. Walls thick enough to print

A printer can only lay down whole lines of plastic. With a standard 0.4 mm nozzle, each line (perimeter) is a little wider than the nozzle. Prusa's guide gives PrusaSlicer's default as 0.45 mm per perimeter, so two perimeters make a wall about 0.9 mm thick, and anything thinner than one perimeter simply can't print.

Practical rules:

  • Aim for at least 1.2 mm on walls that need to hold any load or survive handling.
  • Thin decorative fins, embossed text and small pins under about 1 mm are the usual casualties. Thicken them or accept they'll be soft and fragile.
  • Avoid walls that land between whole perimeter widths if you can; slicers handle them, but the result is less predictable.

5. Overhangs, bridges and supports

FDM builds each layer on top of the last. Anything that sticks out over thin air needs something underneath it.

  • Overhangs up to roughly 45° from vertical usually print cleanly. Prusa says many printers handle 45–60° depending on cooling and settings.
  • Short horizontal bridges between two supports print fine without help.
  • Steeper overhangs need supports: temporary scaffolding that gets removed afterwards and leaves rougher surfaces where it touched.

You can design most supports out:

  • Use a chamfer instead of a rounded fillet on edges facing the bed. Prusa's guide recommends this for a better finish.
  • Make sideways holes teardrop-shaped (pointed at the top) so the top of the hole prints without support.
  • Split awkward parts into pieces that each print flat, then glue or screw them together.

Supports aren't a disaster, but they add plastic, time and clean-up, which all show up in the price. Our post on what 3D printing costs in Australia covers how much.

6. Design in clearance where parts fit together

Printed plastic squishes slightly wider than the design, and holes print slightly small. Two parts drawn at exactly the same size usually won't fit.

Prusa's guide says their printers are accurate to at least 0.2 mm and suggests at least 0.3 mm of clearance for moving parts like hinges. Good starting points:

  • Sliding fit (a lid, a peg in a hole): around 0.2–0.3 mm gap per side
  • Moving parts (hinges, print-in-place mechanisms): 0.3 mm or more
  • Press fit: much tighter, and worth testing

Every printer and material is a little different, so for anything fit-critical, print a small test piece with a few gap sizes before committing to the full part. If you're sending the file to a print service, say in the notes which features need to fit what.

7. Orientation and strength

Prints are weakest between layers. A part pulled in the direction that peels layers apart will fail well before one loaded along them.

  • Lay brackets and clips so the load runs along the layers, not across them.
  • Put the face you care most about either flat on the bed or facing up, away from supports.
  • Keep the largest flat area on the bed where possible, for stability.

If orientation matters for your part, mention it when you order. A print service will usually choose an orientation for printability and may not know which face is cosmetic or which way the load goes.

8. Size, splitting and file format

Check your part fits the printer's build volume. Ours handle parts up to about 250 mm per side; bigger parts get split into sections with pins or dovetails so they line up when joined.

On format: if your software exports 3MF, use it. It's a newer, zip-compressed format that stores units, colours and multiple objects, so the millimetre-versus-inch problem goes away. OBJ is fine too. STL remains the universal fallback, and every slicer reads it.

Before you hit upload

A final pass:

  1. Open the file in a slicer and confirm the size.
  2. Let the slicer check for errors, and fix any it finds.
  3. Preview the sliced layers. Look for missing walls, gaps or features that vanish.
  4. Note anything a printer operator should know: which face is cosmetic, what has to fit what, which way loads go.

When you're ready, you can upload STL, 3MF or OBJ files (in millimetres) to our instant 3D printing quote and see the price straight away. Your card is only held until we've checked the file, and we check every one within a business day, so if something in the mesh looks off, we'll tell you before anything is charged. If you don't have a file yet, or yours needs work, our prototyping and design packages start at $150 for a Rapid Prototype, with small design fixes included.

Got a file you're not sure about? Send it through the quote page and we'll take a look.